Industrial Drawing

Code:

EIG0005

Acronym:

DI

Keywords
Classification	Keyword
OFICIAL	Drawing

Instance: 2007/2008 - 1S

Active?	Yes
Responsible unit:	Industrial Drawing Section
Course/CS Responsible:	Master in Engineering and Industrial Management

Cycles of Study/Courses

Acronym	No. of Students	Study Plan	Curricular Years	Credits UCN	Credits ECTS	Contact hours	Total Time
LGEI	0	Plano de estudos de transição para 2006/07	1	5	5	56	133
MIEIG	89	Plano de estudos de transiçao para 2006/07	1	-	5	56	133
		Syllabus since 2006/2007	1	-	5	56	133

Teaching language

Portuguese

Objectives

SPECIFIC AIMS:

Introduction of the concept of Standardization in general and of its importance in Engineering. Acquisition of deep knowledge about the representation of the nominal shape and dimensions of objects. Development of spatial visualization and technical communication skills. Introduction to the concept of Geometrical product specification (GPS). Introduction to the functional analysis of mechanical systems with the detail drawing of some of their components.

LEARNING OUTCOMES:

At the end of the course, the students shall be able to:

1) Make drawings of objects in orthographic representation and with nominal dimensioning.
2) Read drawings of objects in orthographic representation and make the correspondent pictorial representations (isometric drawings).
3) Make detail drawings of mechanical systems components, through a functional analysis based on the corresponding assembly drawings.

Program

STANDARDIZATION in general and in technical drawings. TECHNICAL PRODUCT DOCUMENTATION: scales, drawing media, ISO lettering and lines. Types of projection systems. Short references to the dihedric method. ORTHOGRAPHIC REPRESENTATIONS: general principles of presentation for views, the choice of views, partial views, auxiliary views, cuts and sections. The reading of orthographic drawings. PICTORIAL REPRESENTATIONS: axonometric representations (isometric drawings). INDICATION OF DIMENSIONS AND TOLERANCES: general principles; dimensioning of angles and slopes on prisms; dimensioning of conical tapers and taper angles; dimensioning of profiles; theory of nominal dimensioning and preferred numbers. GEOMETRICAL PRODUCT SPECIFICATION (GPS): the concept of GPS, The model for geometric specification; fundamental tolerancing principle; dimensional tolerancing - ISO system of limits and fits; geometrical tolerancing (tolerances of form, orientation, location and run-out; datums and datum-systems); tolerancing requirements (envelope, maximum material, least material and reciprocity); general tolerances; indication of surface texture. DETAIL DRAWINGS: geometric dimensioning and tolerancing.

Mandatory literature

Almacinha, J.; Texto de Apoio à Disciplina de Desenho Industrial (MIEIG), AEFEUP, 2007
Morais, José Manuel de Simões; Desenho técnico básico. ISBN: 972-96525-2-X

Complementary Bibliography

International Organization for Standardization; Limits, fits and surface properties. ISBN: 92-67-10288-5
ISO Standards Handbook - TECHNICAL DRAWINGS. Vols 1 e 2, Switzerland: ISO. 4ª ed, 2002
CHEVALIER, A.; Guide du Dessinateur Industriel , Paris: Hachette Technique, 2004
Silva, Arlindo 070; Desenho técnico moderno. ISBN: 972-757-337-1
French, Thomas E.; Engineering drawing and graphic technology. ISBN: 0-07-113302-X
Earle, James H.; Engineering design graphics. ISBN: 0-13-030365-8
Morais, José Manuel de Simões; Desenho básico. ISBN: 972-9247-00-5

Evaluation Type

Distributed evaluation without final exam

Assessment Components

Description	Type	Time (hours)	Weight (%)	End date
Subject Classes	Participação presencial	52,00
Problems solving	Teste	52,00		2008-02-08
	Total:	-	0,00

Amount of time allocated to each course unit

Description	Type	Time (hours)	End date
study	Estudo autónomo	31	2008-02-08
	Total:	31,00