Go to:
Logótipo
Comuta visibilidade da coluna esquerda
Você está em: Start > Publications > View > Modification of carbon nanotubes by ball-milling to be used as ozonation catalysts
Publication

Modification of carbon nanotubes by ball-milling to be used as ozonation catalysts

Title
Modification of carbon nanotubes by ball-milling to be used as ozonation catalysts
Type
Article in International Scientific Journal
Year
2015
Authors
A. G. Gonçalves
(Author)
FEUP
View Personal Page You do not have permissions to view the institutional email. Search for Participant Publications Without AUTHENTICUS Without ORCID
J. J. Delgado
(Author)
Other
The person does not belong to the institution. The person does not belong to the institution. The person does not belong to the institution. Without AUTHENTICUS Without ORCID
J. J. M. Orfão
(Author)
FEUP
View Personal Page You do not have permissions to view the institutional email. Search for Participant Publications View Authenticus page View ORCID page
M. F. R. Pereira
(Author)
FEUP
View Personal Page You do not have permissions to view the institutional email. Search for Participant Publications View Authenticus page View ORCID page
Journal
Title: Catalysis TodayImported from Authenticus Search for Journal Publications
Vol. 249
Pages: 199-203
ISSN: 0920-5861
Publisher: Elsevier
Other information
Authenticus ID: P-00G-2SY
Abstract (EN): Abstract The influence of ball-milling in the texture and surface chemistry of multi-walled carbon nanotubes (MWCNT) was studied in this work. Treatment times up to 360 min at constant frequency (15 vibrations/s) and frequencies from 10 to 20 vibrations/s during 30 min were used for the preparation of the modified samples. These were characterized by nitrogen adsorption at -196°C, temperature programmed desorption (TPD), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). The milled samples were used as catalysts for the ozonation of oxalic acid. The surface area of the MWCNT increases, whereas the particle size decreases with the ball-milling time until 240 min at 15 vibrations/s. The functionalization of MWCNT surface is not achieved by ball-milling under the conditions used. The catalytic performance of the ball-milled samples for oxalic acid mineralization increased significantly when compared to the unmilled MWCNT. Therefore, ball-milling is an effective and simple method to increase the surface area of commercial carbon nanotubes without significant changes of their structural properties, and, consequently, this method allows increasing their catalytic performance in ozonation processes.
Language: English
Type (Professor's evaluation): Scientific
No. of pages: 5
Documents
We could not find any documents associated to the publication with allowed access.
Related Publications

Of the same journal

Special Issue on the 11th International Conference on Catalysis in Membrane Reactors Preface (2014)
Another Publication in an International Scientific Journal
J. M. Sousa; Basile, A; Crespo, J
Introduction (2013)
Another Publication in an International Scientific Journal
Joaquim L Faria; Pilar Fernandez Ibanez; Sixto Malato
Editorial of the special issue carbon for catalysis: CarboCat-VIII symposium (2020)
Another Publication in an International Scientific Journal
Silva, Adrian; Manuel Fernando R Pereira; Joaquim Luís Faria; Figueiredo, JL
Wet peroxide oxidation of dye-containing wastewaters using nanosized Au supported on Al2O3 (2017)
Article in International Scientific Journal
Carmen S. D. Rodrigues; S. A. C. Carabineiro; F. J. Maldonado-Hódar; Luís M. Madeira
Vanadium as a catalyst for NO, N2O and CO2 reaction with activated carbon (2000)
Article in International Scientific Journal
Sónia Carabineiro; Fernandes, FB; Ramos, AM; Vital, J; Silva, IF

See all (114)

Recommend this page Top
Copyright 1996-2024 © Serviços Partilhados da Universidade do Porto I Terms and Conditions I Acessibility I Index A-Z I Guest Book
Page created on: 2024-10-06 11:28:28 | Acceptable Use Policy | Data Protection Policy | Complaint Portal